Simulation the Effect of impact on the Mobile Cover Using Solidworks Anal

  • Serwan Sarbast Mohammed Talabani Department of Manufacturing, College of Engineering, University of Koya, Kurdistan Region, Iraq
  • Ahmad Taifor Azeez Department of Manufacturing, College of Engineering, University of Koya, Kurdistan Region, Iraq
Keywords: Mobile Cover; Mobile Impact; Solidworks

Abstract

Mobile phones are complex and sensitive electronic devices that may be susceptible to fracture if fell down unless shielded securely.Accordingly, Cases are effective means to defend the phones against sudden impact. The performance of these covers relay on many aspects such as design and the potential of the materials. For this reason, it is intended in this project to estimate the effect of the material properties on the impact resistance of the covers using the powerful of Solidworks program. The materials modeled linear elastically and the mobile impacted the ground from a 1 m height under the effect of gravitational force. The results showed that mobile cover made of silicone rubber failed in the impact and polycarbonate shelter was superior to thermoplastic polyurethane rubber cover due to the highest modulus of elasticity. In addition to that, verification of the simulation process was done by comparing the results to the experimental works cited in the literature. It is found that maximum Von Mises stress at the bottom edge and the corners of Gorilla Glass were satisfactory close to the result obtained by Bocko et al.

References

References

Archer, Cohen , Ober, and Rodriguez (2015), Principle of polymer system, 6th edn., Taylor and Francis group.
Attaway, rope system, [online] http://lamountaineers.org/pdf/xRopes.pdf
Beer, Dewolf , Johnston (2006) Mechanics of materials, 4th edition., USA: Mc Graw Hill.
Bocko, Hagara, Hunady, and Lengvarsky (2016),The Methodology for Realization of Smartphone Drop Test Using Digital Image
Correlation, American Journal of Mechanical Engineering, Vol. 4, No. 7, pp. 423- 428. Doi: 10.12691/ajme-4-7-35
Cambridge university engineering department. (2003) Materials Data Book, 3rd edn.,
Chin (2007), Design and Fabrication of Transparent Polycarbonate/ Carbon Nanotube Composite Films. MS. Thesis, The Florida
State University, USA.
Corning Gorilla Glass 3, (2015) Product information.
https://www.corning.com/microsites/csm/gorillaglass/PI_Sheets/CGG_PI_Sheet_Gorilla%20Glass%203.pdf
Ellingham, Kharbas, Manitiu, Scholz, and Turng (2017), Effect of Nucleating Agent and Two- Stage Expansion on The Morphology
and Mechanical Properties of Microcelular Injection Molded Thermoplastic Polyurethane, In: ANTEC, the Plastic Technology
Conference. Anaheim, California, USA, pp. 1461-1467.
Harrison (2003), Drop Test Simulation of Cellular Phone. MSc thesis, Lund University, Lund, Sweden.
Itoh, and Yamada (2006), Measurement of Silicone Rubber Using Impedance Change of a Quartz-Crystal Tuning-Fork Tactile
Sensor. Japanese Journal of Applied Physics, Vol. 45, part 1, number 5B. https://doi.org/10.1143/JJAP.45.4643
Ivankovic, and Kanyanta, (2010), Mechanical characterization of polyurethane elastomer for biomedical applications. Journal of
the Mechanical Behavior of Biomedical Materials, Vol. 3, No. 1, pp. 11.
MIRON and OPREA (2014), Mobile Phones in the Modern Teaching of Physics, Romanian Reports in Physics, 66, 4, pp. 1236–
1252.
Mobile Cases, The Manufacturing Process of Different Types of Mobile Phone. http://mobilecaseshq.com/author/mobilecases/
(Accessed 11 February 2017).
Orth, .Plastic Vs. Rubber Vs. Silicone Phone Cases. https://itstillworks.com/plastic-vs-rubber-vs-silicone-phone-cases-1962.html
(Accessed12February2017)
Published
2019-08-09
How to Cite
Mohammed Talabani, S., and A. Taifor Azeez. “Simulation the Effect of Impact on the Mobile Cover Using Solidworks Anal”. ZANCO Journal of Pure and Applied Sciences, Vol. 31, no. s3, Aug. 2019, pp. 40-46, doi:10.21271/ZJPAS.31.s3.6.